650 GLEASON HYPOID SPIRAL BEVEL GEAR GENERATING MACHINE

650 GLEASON HYPOID SPIRAL BEVEL GEAR GENERATING MACHINE

$39,500 (USD)

orCall 513-771-1952

Description

MODEL NO. 650 GLEASON HYPOID SPIRAL BEVEL GEAR GENERATING MACHINE SERIAL NO. 754202 ( NEW IN 1978 ) SUITABLE FOR THE CUTTING OF LARGER SPIRAL BEVEL, HYPOID, AND ZEROL BEVEL PINIONS AND MATING GEARS UP TO 34” (863.6MM) DIAMETER, 5” (127MM) FACE, WITH 1.08 DP (MODULE 23.5) CUTTING CAPABILITY EQUIPMENT / FEATURES: VARIABLE CUTTER SPEED ARRANGEMENT INCLUDING SET OF SPEED CHANGE GEARS ASSORTED RATIO-OF-ROLL, MODIFIED ROLL, AND INDEX CHANGE GEARS W/TOOL & GEAR CABINET HYDRAULIC CHUCKING ATTACHMENT WITH DRAW-ROD & NUT AUGER-TYPE CHIP CONVEYOR AND MAGNETIC CHIP SEPARATOR CUTTER GUARD AND MANIFOLD FOR HIGH VELOCITY COOLANT SECURITY COVER FOR SET-UP PANEL STANDARD WORK SPINDLE BORE 6” X ¾” TAPER (#60) MODIFIED ROLL MECHANISM, INCLUDING CHANGE GEARS FOR ONE PART ROLL CENTERING SLIDING BASE SET-IN MECHANISM, INCLUDING CONTROLS CRADLE ROTATIONAL SET-OVER, INCLUDING CONTROLS NO ROLL ARRANGEMENT FOR FORMATE AND/OR “DUAL-ROTATION” MACHINE OPTIONS, INCLUDING CONTROLS VARIABLE RATE OF ROLL ARRANGEMENT INCLUDING CONTROLS DOUBLE ROLL ARRANGEMENT, INCLUDING CONTROLS PLUNGE FEED MECHANISM STOCK DIVIDING GAUGE ECCENTRIC SET-OVER ARRANGEMENT INCLUDING CONTROLS RELAY-LOGIC CONTROLS (IN PLACE OF STANDARD PROGRAMMABLE CONTROLLER) COMPLETE ELECTRICAL EQUIPMENT FOR 3-PHASE, 50 OR 60 HZ, 380-550 VOLT INSTALLATION, INCLUDING 110VAC OR 220VAC CONTROL CIRCUIT, TEFC-AC MOTORS (NEMA T-FRAME OR T-FRAME MODIFIED TO IEC DIMENSIONS), DC DRIVE AND CONTROL, AND SINGLE-SPEED CUTTER MOTOR. ELECTRICS WILL COMPLY TO JIC OR IEC TECHNICAL SPECIFICATIONS. DOCUMENTATION TO JIC STANDARDS. * MOST NUMBERS UP TO 120 CAN ALSO BE ACCOMMODATED BUT MAY REQUIRE SPECIAL CHANGE GEARS. ** THIS RADIAL SETTING CAN BE INCREASED TO 18.5” (462.50MM) FOR SOME APPLICATIONS *** MAXIMUM OFFSET APPLIES TO PINION AND GEARS UP TO 25” O.D. FOR 34” DIAMETER GEARS MAXIMUM OFFSET IS 0”

PRICE: F.O.B. OUR WAREHOUSE

Specifications

ManufacturerGLEASON
Model650.0
ConditionUsed
Serial Number754202.0
Stock Number28330
Roof angle range0º TO 90º
Gear diameter – maximum34” (863.6MM)
Maximum radial setting**15.00” **(381MM)
Full depth – maximum1.5” (38.1MM)
Face width – maximum5.000” (127MM)
Coarsest pitch (module)1.08 DP (23.5 MODULE)
Index range *5 TO 80 INCLUSIVE
Work spindle taper hole diameter at large end6” (152.4MM)
Work spindle taper per foot0.75” (19.0MM)
Work spindle depth of taper6” (152.4MM)
Diameter through spindle of hole 5”(1270MM)
Work-head offset above center – maximum***4.5” (114.3MM)
Work-head offset below center – maximum***4.5” (114.3MM)
Machine center to hose of spindle – max23.5” (596.9MM)
Cutter speeds6 TO 167 RPM (STEPLESS)
Motors( 60 HZ ) 50 HZ )
Cutter drive motor, 15hp1800 RPM 1500 RPM
Hydraulic motor, 7.5hp1200 RPM 1500 RPM
Coolant motor, 2hp1200 RPM 1500 RPM
D.c. generating drive motor, 6hp1200 RPM