GLEASON "PHOENIX" #500 HC CNC SPIRAL BEVEL

GLEASON "PHOENIX" #500 HC CNC SPIRAL BEVEL

$89,500 (USD)

orCall 513-771-1952

Description

GLEASON "PHOENIX" #500 HC CNC SPIRAL BEVEL GEAR GENERATOR NEW 1995, SERIAL NO. 893801, MODEL NO. 500HC SUITABLE FOR THE CUTTING OF SPIRAL BEVEL AND HYPOID GEARS AND PINIONS UP TO 30” (762MM) DIAMETER VIA “FACE-MILLING”, AND 22” (558.8MM) VIA “FACE-HOBBING” METHOD UTILIZING THE TRI-AC CUTTING SYSTEM EQUIPMENT / FEATURES: GE-FANUC 150M COMPUTER CONTROL WITH SPIRAL BEVEL GEAR CUTTING SOFTWARE, CYCLE FAULT MONITORING, AND MEMORY CAPACITY FOR 25 PARTS, WITH AUTOMATIC SETUP AND CONTROL OF SIX (6) AXES: WORK SPINDLE ROTATIONAL AXIS (A) HORIZONTAL LINEAR MOTION OF CUTTER AXIS (X) SWINGING BASE OF WORK-SPINDLE AXIS (B) VERTICAL LINEAR MOTION OF CUTTER AXIS (Y) CUTTER SPINDLE ROTATIONAL AXIS (C) SLIDING BASE LINEAR MOTION OF WORK-SPINDLE AXIS (Z) MACHINE FURNISHED WITH FREESTANDING, AIR CONDITIONED ELECTRICAL ENCLOSURE. OPERATOR’S PENDANT LOCATED AT FRONT OF MACHINE ADJACENT TO POWERED ACCESS DOOR. THE SPIRAL BEVEL GEAR CUTTING SOFTWARE ON THE 500HC MACHINE WOULD BE CAPABLE OF PERFORMING THE FOLLOWING CUTTING PROCESSES: FACE MILLING COMPLETE GENERATED AND FORMATE GEARS COMPLETE PINIONS OF GENERATED OR FORMATE PAIRS ROUGH GENERATED OR FORMATE GEARS ROUGH PINIONS OF GENERATED OR FORMATE PAIRS ROUGH SLOT AND FINISH FIRST SIDE OF PINIONS USING ANY SINGLE SIDE MODIFIED ROLL DEVELOPMENT METHOD FINISH GENERATED OR FORMATE (NOT SINGLE CYCLE) GEARS FINISH PINIONS USING AND SINGLE SIDE TILT OR MODIFIED ROLL DEVELOPMENT METHOD FACE HOBBING COMPLETE GENERATED OR FORMATE GEARS COMPLETE PINIONS OR GENERATED OR FORMATE PAIRS EQUIPMENT COMPLETE COOLANT PLANT, PUMP TANK & PIPING WITH MAGNETIC CHIP CONVEYOR. HYDRAULIC WORKPIECE CHUCK WITH DRAW-ROD. WORK-SPINDLE BORE 8” (#80 TAPER) WITH OPTIONAL ADAPTER TO 6” (#60 TAPER). COMPLETE SET OF WORK SPINDLE RATIO GEARS. TOTALLY ENCLOSED WORK-AREA GUARDING WITH POWERED ACCESS DOOR. WORK CHAMBER AND CONTROL BOX LIGHTING. PRODUCTION AND SHARPEN-CUTTER COUNT DISPLAY CLAMPING AND EJECTING EQUIPMENT FOR GLEASON RSR-TYPE SPIRAL FACE MILLING CUTTERS 9” THROUGH 18” DIAMETER AND GLEASON TRI-AC SPIRAL FACE HOBBING CUTTERS 176MM THROUGH 350MM DIAMETER. MANUAL STOCK DIVIDER. FORMATE SINGLE CYCLE GEAR FINISHING ARRANGEMENT. SMOKE AND MIST COLLECTOR. CHILLER UNIT FOR COOLANT SYSTEM. WORK ARBOR CLAMP (FOR GEARS GREATER THAN 15” IN DIAMETER). ELECTRICAL EQUIPMENT FOR 380 VOLT, 50 HZ, OR 460 VOLT, 60 HZ, 3-PHASE INSTALLATION. CONTROL CIRCUIT IS 110 VAC WITH 24 VDC INPUT AND 24 VAC OUTPUT TRANSFORMER TO CONVERT LINE VOLTAGES OF 200 TO 240 VOLT, 50 OR 60 HZ TO 400 VOLT (FOR 50 HZ) OR 460 VOLT (FOR 60 HZ). FULL MACHINE DOCUMENTATION FOR THE MACHINE AND CONTROLLER, REPLACEMENT PARTS LIST, HYDRAULIC AND ELECTRICAL DIAGRAMS PRICE: F.O.B. OUR WAREHOUSE

Specifications

Model500HC
Year1995
ConditionUsed
Serial Number893801.0
Stock Number27691
Root angle range (b axis)-5º TO 90º-5º TO 90º
Max horiz travel(-305MM TO +305MM)
Max vert travel (y)(-305MM TO +305MM)
Sliding base travel (z)(-51MM TO +711MM)
Machine center to work spindle face9.00” (229MM)
Full depth (maximum).93”(23.50MM)
Face width (maximum)3.00”(76.20MM)
Tooth number5 TO 200 INCLUSIVE
Cutter diameters(400,500MM)(350MM)
Work spindle, a-axis0-67 RPM 0-333 RPM
Swinging base, b-axis0 TO 30 DEG/SEC N/A
Cutter, c-axis30 TO 240 RPM
X horizontal, x-axis0 TO 80MM/SEC
Y vertical, y-axis0 TO 80MM/SEC
Z sliding base, z-axis0 TO 80MM/SEC
Diameter of taper hole at large end8” (#80 TAPER)
Includes optional adapter sleeve to6” (#60 TAPER)
Depth of taper 6”152.40MM
A-axis work spindle ac servo50.0 66.0
B-axis swinging base ac servo4.4 5.9
C-axis cutter spindle ac drive226.7 307.3
X-axis horizontal ac servo8.7 11.8
Y-axis vertical ac servo8.7 11.8
Z-axis sliding base ac servo8.7 11.8
Coolant ac induction5 HP
Hydraulc ac induction5 HP
Chiller ac induction3 HP
Chip conveyor½ HP
Length x width(557CM X 576CM)
Height127” (322CM)
Weight (approximately)42,500 LBS(19,318 KGS)