650 GLEASON HYPOID SPIRAL BEVEL GEAR GENERATING MACHINE

MODEL NO. 650 GLEASON HYPOID SPIRAL BEVEL GEAR GENERATING MACHINE SERIAL NO. 754202 ( NEW IN 1978 ) SUITABLE FOR THE CUTTING OF LARGER SPIRAL BEVEL, HYPOID, AND ZEROL BEVEL PINIONS AND MATING GEARS UP TO 34” (863.6MM) DIAMETER, 5” (127MM) FACE, WITH 1.08 DP (MODULE 23.5) CUTTING CAPABILITY EQUIPMENT / FEATURES: VARIABLE CUTTER SPEED ARRANGEMENT INCLUDING SET OF SPEED CHANGE GEARS ASSORTED RATIO-OF-ROLL, MODIFIED ROLL, AND INDEX CHANGE GEARS W/TOOL & GEAR CABINET HYDRAULIC CHUCKING ATTACHMENT WITH DRAW-ROD & NUT AUGER-TYPE CHIP CONVEYOR AND MAGNETIC CHIP SEPARATOR CUTTER GUARD AND MANIFOLD FOR HIGH VELOCITY COOLANT SECURITY COVER FOR SET-UP PANEL STANDARD WORK SPINDLE BORE 6” X ¾” TAPER (#60) MODIFIED ROLL MECHANISM, INCLUDING CHANGE GEARS FOR ONE PART ROLL CENTERING SLIDING BASE SET-IN MECHANISM, INCLUDING CONTROLS CRADLE ROTATIONAL SET-OVER, INCLUDING CONTROLS NO ROLL ARRANGEMENT FOR FORMATE AND/OR “DUAL-ROTATION” MACHINE OPTIONS, INCLUDING CONTROLS VARIABLE RATE OF ROLL ARRANGEMENT INCLUDING CONTROLS DOUBLE ROLL ARRANGEMENT, INCLUDING CONTROLS PLUNGE FEED MECHANISM STOCK DIVIDING GAUGE ECCENTRIC SET-OVER ARRANGEMENT INCLUDING CONTROLS RELAY-LOGIC CONTROLS (IN PLACE OF STANDARD PROGRAMMABLE CONTROLLER) COMPLETE ELECTRICAL EQUIPMENT FOR 3-PHASE, 50 OR 60 HZ, 380-550 VOLT INSTALLATION, INCLUDING 110VAC OR 220VAC CONTROL CIRCUIT, TEFC-AC MOTORS (NEMA T-FRAME OR T-FRAME MODIFIED TO IEC DIMENSIONS), DC DRIVE AND CONTROL, AND SINGLE-SPEED CUTTER MOTOR. ELECTRICS WILL COMPLY TO JIC OR IEC TECHNICAL SPECIFICATIONS. DOCUMENTATION TO JIC STANDARDS. * MOST NUMBERS UP TO 120 CAN ALSO BE ACCOMMODATED BUT MAY REQUIRE SPECIAL CHANGE GEARS. ** THIS RADIAL SETTING CAN BE INCREASED TO 18.5” (462.50MM) FOR SOME APPLICATIONS *** MAXIMUM OFFSET APPLIES TO PINION AND GEARS UP TO 25” O.D. FOR 34” DIAMETER GEARS MAXIMUM OFFSET IS 0” PRICE: F.O.B. OUR WAREHOUSE Roof angle range: 0º TO 90º Gear diameter – maximum: 34” (863.6MM) Maximum radial setting: **15.00” **(381MM) Full depth – maximum: 1.5” (38.1MM) Face width – maximum: 5.000” (127MM) Coarsest pitch (module): 1.08 DP (23.5 MODULE) Index range *: 5 TO 80 INCLUSIVE Work spindle taper hole diameter at large end: 6” (152.4MM) Work spindle taper per foot: 0.75” (19.0MM) Work spindle depth of taper: 6” (152.4MM) Diameter through spindle of hole 5”: (1270MM) Work-head offset above center – maximum: ***4.5” (114.3MM) Work-head offset below center – maximum: ***4.5” (114.3MM) Machine center to hose of spindle – max: 23.5” (596.9MM) Cutter speeds: 6 TO 167 RPM (STEPLESS) Motors: ( 60 HZ ) 50 HZ ) Cutter drive motor, 15hp: 1800 RPM 1500 RPM Hydraulic motor, 7.5hp: 1200 RPM 1500 RPM Coolant motor, 2hp: 1200 RPM 1500 RPM D.c. generating drive motor, 6hp: 1200 RPM